STAUFF · Replacement Elements · inline line

SE-125-A-10-V filter element: specifications & equivalents

Name: SE-125-A-10-V filter element — STAUFF specifications and cross references
Brand: STAUFF

The SE-125-A-10-V is a STAUFF inline-line hydraulic filter element, sized 60 × 371 mm OD × length (ID 34.2 mm). Verify against the current manufacturer data sheet before ordering.

Envelope OD × L 60 × 371 mm

Inside diameter 34.2 mm

Line type inline

Partially verified. Fit and grade trace to an official interchange document; dimensional values are compiled from 0 aftermarket listing(s) and must be confirmed against the manufacturer housing drawing. Confidence score 0.85.

Micron rating, media type, collapse pressure and seal material are not printed in the STAUFF interchange listing and are pending extraction from STAUFF product data sheets. Verify against the current STAUFF catalog before ordering.

Specification table

Parameter	Value
Filter type	inline line
Outside diameter OD	60 mm
Inside diameter ID	34.2 mm
Length	371 mm
End caps	open-ended cartridge element
Integral bypass valve	none (housing/valve-dependent)
Source catalog	STAUFF: STAUFF Filter Interchange online database (filterinterchange.com)
Last verified	2026-09-27

Sources: STAUFF — STAUFF Filter Interchange online database (filterinterchange.com) — accessed 2026-09-27.

STAUFF® and all model designations are trademarks of their respective owners, used here for identification only — ElementRef is an independent reference site, not an authorized STAUFF distributor.

Dimensions & series range

Outside diameter	60 mm (2.362 in)
Inside diameter	34.2 mm (1.346 in)
Overall length	371 mm (14.606 in)

All 60×371 mm interchange elements →

Cross references & equivalents

Equivalent model	Brand	Match level	Note
↔ 01262265 page in verification queue	UFI	partial	STAUFF Filter Interchange lists 01262265 (HYDAC) as replaced by SE-125-A-10-V. Envelope dimensions are published; media grade and performance data are not — confirm before substituting in cleanliness-critical circuits.
↔ 01262285 page in verification queue	UFI	partial	STAUFF Filter Interchange lists 01262285 (HYDAC) as replaced by SE-125-A-10-V. Envelope dimensions are published; media grade and performance data are not — confirm before substituting in cleanliness-critical circuits.
↔ 1262265 page in verification queue	UFI	partial	STAUFF Filter Interchange lists 1262265 (HYDAC) as replaced by SE-125-A-10-V. Envelope dimensions are published; media grade and performance data are not — confirm before substituting in cleanliness-critical circuits.

Interchange levels: full catalog-confirmed drop-in · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the SE-125-A-10-V model number is decoded

SE-125-A-10-VSTAUFF replacement element part number per the STAUFF Filter Interchange database.

Typical equipment & applications

Replacement element for OEM hydraulic filter housings

Selection pitfalls — read before you substitute

“10 µm nominal” and “12 µm at β1000” can describe the very same media — one is reported at β≥200, the other at β≥1000 per ISO 16889. Compare ratings at the same Beta test point, not just the printed micron number.
Nitrile (NBR) seals are standard for mineral hydraulic oil but fail early in some phosphate-ester fluids and at sustained high temperature; verify seal compound against the fluid data sheet (fluorocarbon/Viton executions may be required).
End-cap geometry and the number/position of O-rings block interchange even when OD and length match — visually compare end caps before fitting, especially with aftermarket cartridges.

Frequently asked questions

What are the dimensions of the SE-125-A-10-V filter element?

The published envelope is 60 mm OD × 371 mm length with a 34.2 mm inside diameter (2.362 × 14.606 in × 1.346 in ID). Confirm against the housing drawing before ordering.

What replaces the SE-125-A-10-V filter element?

3 partial match(es) requiring parameter review

How do I read the SE-125-A-10-V part number?

See the designation decoder above: each segment of SE125A10V encodes size, line type, filtration grade and media/collapse execution.

Is a same-envelope aftermarket element always a drop-in replacement?

No. Matching OD and length only proves the cartridge fits the bowl. End-cap style, seal compound, micron/Beta rating, collapse pressure and bypass configuration must also match; the table above tags every equivalent as full, partial or verify for exactly this reason.

How often should a hydraulic return-line element be replaced?

Replace at the housing manufacturer’s recommended differential-pressure setting (commonly signalled by a clogging indicator), or on a time-based service interval when no indicator is fitted — never wait for bypass to open continuously, because unfiltered oil then reaches the valves.

Same-envelope elements from other brands

View full interchange →

These 10 catalog element(s) share the 60×371 mm envelope. Envelope match alone does not guarantee interchangeability — compare micron/Beta, seals and collapse rating.

SE-125-A-03-B STAUFF SE-125-A-03-V STAUFF SE-125-A-05-B STAUFF SE-125-A-05-V STAUFF SE-125-A-10-B STAUFF SE-125-A-20-B STAUFF SE-125-A-20-V STAUFF SE-125-B-200-B STAUFF SE-125-B-25-B STAUFF SE-125-B-50-V STAUFF

Other models in the Replacement Elements series

All 3832 →

AD-030-B-125-B 83×193 mm AD-030-B-40-B 83×193 mm AD-030-B-60-B 83×193 mm AD-030-B-80-B 83×193 mm AD-030-E-20-B 83×193 mm AD-033-B-40-B 89×226 mm AD-033-B-60-B 89×226 mm AD-033-B-80-B 89×226 mm FE-BL-200 85×61 mm FE-BL-500 190×105 mm

Reviewed & verified by the ElementRef engineering desk against STAUFF on 2026-09-27. Read our editorial & correction policy.