HYDAC · Betamicron 4 D/DN · pressure line

0250 DN 020 BH4HC filter element: specifications & equivalents

The 0250 DN 020 BH4HC is a HYDAC pressure-line hydraulic filter element, built with betamicron 4 microglass, high-collapse (210 bar / 3045 psi) media, sized 80 × 250 mm OD × length (ID 40.1 mm), rated at 20 µm absolute (βx(c) ≥ 1000 per ISO 16889). Verify against the current manufacturer data sheet before ordering.

Envelope OD × L 80 × 250 mm

Inside diameter 40.1 mm

Filtration rating 20 µm abs.

Beta rating β x(c) ≥ 1000 per ISO 16889

Media Betamicron 4 microglass, high-collapse (210 bar / 3045 psi)

Collapse / burst 210 bar

Line type pressure

Catalog verified. Parameters extracted from the manufacturer’s electronic catalog / official interchange document and checked 2026-09-27. Confidence score 0.95.

Specification table

Parameter	Value
Filter type	pressure line
Media	Betamicron 4 microglass, high-collapse (210 bar / 3045 psi)
Filtration rating	20 µm
Rating basis	absolute
Beta ratio	βx(c) ≥ 1000 per ISO 16889
Outside diameter OD	80 mm
Inside diameter ID	40.1 mm
Length	250 mm
End caps	O-ring cap one end, closed cap other end
Flow direction	outside-in
Collapse / burst pressure	210 bar
Integral bypass valve	none (housing/valve-dependent)
Seal material	Nitrile (NBR)
Operating temperature	-30 to 100 °C
Manufacturer part no.	2213953
Source catalog	HYDAC Technology Corporation: HYDAC Filter Elements HYDAC / Airline Hydraulics: Betamicron Filter Elements
Last verified	2026-09-27

Sources: HYDAC Technology Corporation — HYDAC Filter Elements · HYDAC / Airline Hydraulics — Betamicron Filter Elements — accessed 2026-09-26.

HYDAC® and all model designations are trademarks of their respective owners, used here for identification only — ElementRef is an independent reference site, not an authorized HYDAC distributor.

Dimensions & series range

Outside diameter	80 mm (3.150 in)
Inside diameter	40.1 mm (1.579 in)
Overall length	250 mm (9.843 in)

All 80×250 mm interchange elements →

Cross references & equivalents

No catalog-verified cross references yet. This model is in the manual verification queue — request a verified equivalent.

Interchange levels: full catalog-confirmed drop-in · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 0250 DN 020 BH4HC model number is decoded

0250Element size code (0250) for the DIN 24550 housing family.
DNDIN 24550 standard envelope element.
02020 µm absolute class per the HYDAC electronic catalog (s2).
BH4HCBetamicron 4 microglass, high-collapse (210 bar / 3045 psi)

Typical equipment & applications

Pressure-line hydraulic filters upstream of control valves
High-differential-pressure industrial hydraulic circuits
Hydraulic power units for steel, paper and power generation

Selection pitfalls — read before you substitute

“10 µm nominal” and “12 µm at β1000” can describe the very same media — one is reported at β≥200, the other at β≥1000 per ISO 16889. Compare ratings at the same Beta test point, not just the printed micron number.
Nitrile (NBR) seals are standard for mineral hydraulic oil but fail early in some phosphate-ester fluids and at sustained high temperature; verify seal compound against the fluid data sheet (fluorocarbon/Viton executions may be required).
End-cap geometry and the number/position of O-rings block interchange even when OD and length match — visually compare end caps before fitting, especially with aftermarket cartridges.

Frequently asked questions

What are the dimensions of the 0250 DN 020 BH4HC filter element?

The published envelope is 80 mm OD × 250 mm length with a 40.1 mm inside diameter (3.150 × 9.843 in × 1.579 in ID). Confirm against the housing drawing before ordering.

What micron rating does 0250 DN 020 BH4HC use?

This element is rated 20 µm absolute — βx(c) ≥ 1000 per ISO 16889. Always compare Beta ratings at the same test point: two brands may print different micron numbers for the same physical grade.

What replaces the 0250 DN 020 BH4HC filter element?

Cross references are being verified for this model — use the inquiry form and the engineering desk will confirm equivalents.

How do I read the 0250 DN 020 BH4HC part number?

See the designation decoder above: each segment of 0250DN020BH4HC encodes size, line type, filtration grade and media/collapse execution.

Is a same-envelope aftermarket element always a drop-in replacement?

No. Matching OD and length only proves the cartridge fits the bowl. End-cap style, seal compound, micron/Beta rating, collapse pressure and bypass configuration must also match; the table above tags every equivalent as full, partial or verify for exactly this reason.

How often should a hydraulic return-line element be replaced?

Replace at the housing manufacturer’s recommended differential-pressure setting (commonly signalled by a clogging indicator), or on a time-based service interval when no indicator is fitted — never wait for bypass to open continuously, because unfiltered oil then reaches the valves.

Same-envelope elements from other brands

View full interchange →

These 22 catalog element(s) share the 80×250 mm envelope. Envelope match alone does not guarantee interchangeability — compare micron/Beta, seals and collapse rating.

0250 DN 003 BH4HC HYDAC · 3 µm 0250 DN 005 BH4HC HYDAC · 5 µm 0250 DN 006 BH4HC HYDAC · 6 µm 0250 DN 010 BH4HC HYDAC · 10 µm SS-100-B-100-B STAUFF SS-100-B-25-B STAUFF SS-100-B-25-V STAUFF SS-100-B-40-B STAUFF SS-100-B-60-B STAUFF SS-100-B-60-V STAUFF

Other models in the Betamicron 4 D/DN series

All 90 →

0240 D 003 BH4HC 3 µm 0240 D 005 BH4HC 5 µm 0240 D 006 BH4HC 6 µm 0240 D 010 BH4HC 10 µm 0240 D 020 BH4HC 20 µm 0250 DN 003 BH4HC 80×250 mm · 3 µm 0250 DN 005 BH4HC 80×250 mm · 5 µm 0250 DN 006 BH4HC 80×250 mm · 6 µm 0250 DN 010 BH4HC 80×250 mm · 10 µm 0330 D 003 BH4HC 3 µm

Reviewed & verified by the ElementRef engineering desk against HYDAC Technology Corporation and HYDAC / Airline Hydraulics on 2026-09-27. Read our editorial & correction policy.